6/13/2023 0 Comments Installing vinyl plank flooringNext, roll the complete floor to ensure good adhesive transfer. Use the same procedure to complete the other side of the room.Ĩ. It is strongly recommended to stagger the rows so that the short edge seams are not in a straight uniform line.Ħ.Place each plank in place, with pressure applied over each plank.ħ. Install planks and roll to ensure good adhesionĥ. Sanding to smooth the joints is recommended with a primer applied to these areas to assist plank adhesion. Preferably apply a second levelling layer. If necessary, use a levelling compound to level all joints between the tiles. Refer to Timber Underlayment manufactures installation guidelines and recommendations. Vinyl and Cork cement sheets should be used in wet areas. The timber floor now needs to be sheeted with a timber underlayment such as Ply Board or Masonite. If a high moisture content is prevalent, an appropriate moisture barrier/sealant is recommended to be applied during vinyl plank installation in accordance with the manufacturer’s instructions.Ĭoncrete substrate moisture content details are available in the current Australian Standard “Floor Coverings - 1884-2012 Resilient Sheet & Tiles - Laying & Maintenance Practices” The moisture content of the subfloor should not exceed 75% RH (In-Situ Probe test method.)Ĭarefully remove all debris (including loose nails), sweep and vacuum. Whilst not always required, it is recommended Indentations and uneven concrete subfloors should be treated with the appropriate cementitious screed or levelling compound and be in accordance with manufacturer’s recommendations and guidelines. It is recommended to test all concrete substrates for moisture content, according to the current Australian Standards prior to your DIY installing vinyl plank flooring installation.Īll soft floor coverings and its debris should be removed before installation. The minimum subfloor temperature before commencing surface preparation and application is 10o C. Sub-floors should be free from wax, grease, paint, previously-used adhesive, curing compounds, hydrostatic pressure and any other impurities that may affect adhesion. To be in accordance with the current Australian Standard “Floor Coverings –1884-2012 Resilient Sheet & Tiles – Laying & Maintenance Practices,” all surfaces to be bonded should be absorbent, dry, smooth, intact and clean. Opening the ends of boxes to assist acclimatisation is recommended Cartons should be acclimatised next to each other on a flat surface. The temperature needs to be maintained prior to, during and for at least 24 hours after installation is completed. Planks must be stored between 18☌ - 25☌, for a period of at least 48 hours before installation. Ustik Luxury Vinyl Planks must be allowed to acclimatise in the room of installations. Store and transport cartons on a flat surface in neat stacks, store cartons flat, and never put them upright.ĭo not store Ustik Luxury Vinyl Planks in moist or dusty rooms or places with extreme temperatures. Switch off your floor heating 24h before and after installation.įor best results after installation, premises should be kept in a temperature range of 15 - 28☌.Īlways handle, store and transport Ustik Luxury DIY vinyl plank flooring planks carefully to prevent distortions. To ensure professional self adhesive vinyl installation, it is also important to keep the subfloor in the above-mentioned temperature range to counteract dimensional variations.įloor heating can be used with Ustik Luxury Vinyl Planks up to a maximum contact temperature of 27☌. Always ensure that the joints are staggered by at least 15cm (6 inches).ĭuring the installation procedure ensure that the indoor climate conditions are always kept between 18 - 25☌. The floor should preferably be installed parallel to how the light enters the room.Įnsure that the end joints of the planks in 2 successive rows are never in a line. Make sure the DIY vinyl planks are sufficiently mixed when you install them so that you don’t end up with too many identical, light or dark planks in the same area.Ĭheck all planks in daylight before and during installation. The compatibility of planks in repeated orders cannot be guaranteed. For installing vinyl plank flooring, we recommend ordering all vinyl plank floors for installation for the same flooring project at the same time.
0 Comments
Leave a Reply. |